CCNA 2 Chapter 2 v5.02 Exam Answers 2015

You can download fresh questions. Daily updated. 

LAST UPDATE: TODAY 

1 
Which type of cable does a network administrator need to connect a PC to a switch to recover it after the Cisco IOS software fails to load?

a coaxial cable

a crossover cable

a straight-through cable

a console cable*

2 
Which two basic functions are performed by network security tools? (Choose two.)

writing a security policy document for protecting networks

controlling physical access to user devices

revealing the type of information an attacker is able to gather from monitoring network traffic*

simulating attacks against the production network to determine any existing vulnerabilities*

educating employees about social engineering attacks

3 
While troubleshooting a connectivity problem, a network administrator notices that a switch port status LED is alternating between green and amber. What could this LED indicate?

A PC is using the wrong cable to connect to the port.

The port has an active link with normal traffic activity.

The port is administratively down.

The port has no link.

The port is experiencing errors.*

4

Refer to the exhibit. The network administrator wants to configure Switch1 to allow SSH connections and prohibit Telnet connections. How should the network administrator change the displayed configuration to satisfy the requirement?

Reconfigure the RSA key.

Configure SSH on a different line.

Use SSH version 1.

Modify the transport input command.*

5

Open the PT Activity. Perform the tasks in the activity instructions and then answer the question.
Fill in the blank.
Do not use abbreviations.What is the missing command on S1? “ ip address 192.168.99.2 255.255.255.0 ”

The ip address 192.168.99.2 255.255.255.0 command is missing on interface vlan 99, the management VLAN.​

6 
Which three statements are true about using full-duplex Fast Ethernet? (Choose three.)

Performance is improved with bidirectional data flow.*

Performance is improved because the NIC is able to detect collisions.

Latency is reduced because the NIC processes frames faster.

Full-duplex Fast Ethernet offers 100 percent efficiency in both directions.*

Nodes operate in full-duplex with unidirectional data flow.

Performance is improved because the collision detect function is disabled on the device.*
7 
In which type of attack does a malicious node request all available IP addresses in the address pool of a DHCP server in order to prevent legitimate hosts from obtaining network access?​

CAM table overflow

DHCP starvation*

MAC address flooding

DHCP snooping

8 
Which protocol or service sends broadcasts containing the Cisco IOS software version of the sending device, and the packets of which can be captured by malicious hosts on the network?

DNS

CDP*

DHCP

SSH

9 
Which two statements are true regarding switch port security? (Choose two.)

The three configurable violation modes all require user intervention to re-enable ports.

The three configurable violation modes all log violations via SNMP.

After entering the sticky parameter, only MAC addresses subsequently learned are converted to secure MAC addresses.

Dynamically learned secure MAC addresses are lost when the switch reboots.*

If fewer than the maximum number of MAC addresses for a port are configured statically, dynamically learned addresses are added to CAM until the maximum number is reached.*
10 
The network administrator enters the following commands on a Cisco switch:

Switch(config)# interface vlan1
Switch(config-if)# ip address 192.168.1.2 255.255.255.0
Switch(config-if)# no shutdown

What is the effect of entering these commands?

The address of the default gateway for this LAN is 192.168.1.2/24.

Users on the 192.168.1.0/24 subnet are able to ping the switch at IP address 192.168.1.2.*

All devices attached to this switch must be in the 192.168.1.0/24 subnet to communicate.

The switch is able to forward frames to remote networks.

11

Refer to the exhibit. Port Fa0/2 has already been configured appropriately. The IP phone and PC work properly. Which switch configuration would be most appropriate for port Fa0/2 if the network administrator has the following goals?
No one is allowed to disconnect the IP phone or the PC and connect some other wired device.
If a different device is connected, port Fa0/2 is shut down.
The switch should automatically detect the MAC address of the IP phone and the PC and add those addresses to the running configuration.

SWA(config-if)# switchport port-security
SWA(config-if)# switchport port-security maximum 2
SWA(config-if)# switchport port-security mac-address sticky********

SWA(config-if)# switchport port-security
SWA(config-if)# switchport port-security maximum 2
SWA(config-if)# switchport port-security mac-address sticky
SWA(config-if)# switchport port-security violation restrict

SWA(config-if)# switchport port-security mac-address sticky
SWA(config-if)# switchport port-security maximum 2

SWA(config-if)# switchport port-security
SWA(config-if)# switchport port-security mac-address sticky
12

Refer to the exhibit. Which event will take place if there is a port security violation on switch S1 interface Fa0/1?

A notification is sent.

The interface will go into error-disabled state.

A syslog message is logged.

Packets with unknown source addresses will be dropped.*

13 
Which method would mitigate a MAC address flooding attack?

using ACLs to filter broadcast traffic on the switch​

increasing the speed of switch ports

increasing the size of the CAM table

configuring port security*

14

Refer to the exhibit. What media issue might exist on the link connected to Fa0/1 based on the show interface command?

The interface might be configured as half-duplex.

The bandwidth parameter on the interface might be too high.

There could be too much electrical interference and noise on the link.*

The cable attaching the host to port Fa0/1 might be too long.

There could be an issue with a faulty NIC.

15 
Fill in the blank.
” Full-duplex” communication allows both ends of a connection to transmit and receive data simultaneously.

Full-duplex communication improves the performance of a switched LAN, increasing effective bandwidth by allowing both ends of a connection to transmit and receive data simultaneously.

16 
Which interface is the default location that would contain the IP address used to manage a 24-port Ethernet switch?

VLAN 1*

VLAN 99

Fa0/0

Fa0/1

interface connected to the default gateway

17 
Which action will bring an error-disabled switch port back to an operational state?

Issue the switchport mode access command on the interface.

Remove and reconfigure port security on the interface.

Clear the MAC address table on the switch.

Issue the shutdown and then no shutdown interface commands.*
18

Refer to the exhibit. What can be determined about port security from the information that is shown?

The port has been shut down.

The port has the maximum number of MAC addresses that is supported by a Layer 2 switch port which is configured for port security.

The port violation mode is the default for any port that has port security enabled.*

The port has two attached devices.
19

Place the options in the following order:
step 3
– not scored –
step 1 
step 4 
step 2 
step 5 
step 6

20 
Fill in the blank.
When port security is enabled, a switch port uses the default violation mode of    ”   shutdown  ”    until specifically configured to use a different violation mode.

If no violation mode is specified when port security is enabled on a switch port, then the security violation mode defaults to shutdown.

21

Refer to the exhibit. Which S1 switch port interface or interfaces should be configured with the ip dhcp snooping trust command if best practices are implemented?

only the G0/1 and G0/24 ports*

only unused ports

only the G0/2, G0/3, and G0/4 ports

only the G0/1 port

only the G0/1, G0/2, G0/3, and G0/4 ports
22 
What impact does the use of the mdix auto configuration command have on an Ethernet interface on a switch?

automatically assigns the first detected MAC address to an interface

automatically detects duplex settings

automatically detects copper cable type*

automatically detects interface speed
23 
Which command displays information about the auto-MDIX setting for a specific interface?​

show interfaces

show processes

show running-config

show controllers*
24 
A production switch is reloaded and finishes with a Switch> prompt. What two facts can be determined? (Choose two.)

There is not enough RAM or flash on this router.

The switch did not locate the Cisco IOS in flash, so it defaulted to ROM.

A full version of the Cisco IOS was located and loaded.*

The boot process was interrupted.

POST occurred normally.*

NEW QUESTION

 25. Which two statements are true about using full-duplex Fast Ethernet?

Performance is improved with bidirectional data flow.*
Latency is reduced because the NIC processes frames faster.
Nodes operate in full-duplex with unidirectional data flow.
Performance is improved because the NIC is able to detect collisions.
Full-duplex Fast Ethernet offers 100 percent efficiency in both directions.*

26. A network administrator configures the port security feature on a switch. The security policy specifies that each access port should allow up to two MAC addresses. When the maximum number of MAC addresses is reached, a frame with the unknown source MAC address is dropped and a notification is sent to the syslog server. Which security violation mode should be configured for each access port?

warning
protect
shutdown
restrict*

27. Identify the steps needed to configure a switch for SSH.
Place the options in the following order:
[+] Create a local user.
[+] Generate RSA keys.
[+] Configure a domain name.
[+] Use the login local command.
[+] Use the transport input ssh command.
[+] Order does not matter within this group.

28. An administrator wants to use a network security auditing tool on a switch to verify which ports are not protected against a MAC flooding attack. For the audit to be successful, what important factor must the administrator consider?

if the number of valid MAC addresses and spoofed MAC addresses is the same
if the CAM table is empty before the audit is started
if all the switch ports are operational at the same speed
the aging-out period of the MAC address table*

29. Which two features on a Cisco Catalyst switch can be used to mitigate DHCP starvation and DHCP spoofing attacks? (Choose two.)

port security*
DHCP snooping*
extended ACL
strong password on DHCP servers
DHCP server failover

30. What is one difference between using Telnet or SSH to connect to a network device for management purposes?

Telnet uses UDP as the transport protocol whereas SSH uses TCP.
Telnet supports a host GUI whereas SSH only supports a host CLI.
Telnet does not provide authentication whereas SSH provides authentication.
Telnet sends a username and password in plain text, whereas SSH encrypts the username and password.*

31. Refer to the exhibit. A network technician is troubleshooting connectivity issues in an Ethernet network with the command show interfaces fastEthernet 0/0. What conclusion can be drawn based on the partial output in the exhibit?

All hosts on this network communicate in full-duplex mode.
There are collisions in the network that cause frames to occur that are less than 64 bytes in length.
A malfunctioning NIC can cause frames to be transmitted that are longer than the allowed maximum length. *
Some workstations might use an incorrect cabling type to connect to the network.

32. In which situation would a technician use the show interfaces switch command?

when packets are being dropped from a particular directly attached host*
when an end device can reach local devices, but not remote devices
to determine the MAC address of a directly attached network device on a particular interface
to determine if remote access is enabled

33. Which statement describes the port speed LED on the Cisco Catalyst 2960 switch?
If the LED is off, the port is not operating.
If the LED is blinking green, the port is operating at 10 Mb/s.
If the LED is green, the port is operating at 100 Mb/s.*
If the LED is amber, the port is operating at 1000 Mb/s.

34. Match the Link State to the interface and protocol status.
Place the options in the following order:
disable -admin down
Layer 1 problem -down/down
– not scored –
Layer 2 problem -up/down
operational -up/up

35. What is a function of the switch boot loader?

to provide security for the vulnerable state when the switch is booting
to control how much RAM is available to the switch during the boot process
to speed up the boot process
to provide an environment to operate in when the switch operating system cannot be found*