CCNA 1 Chapter 8 v5 Exam Answers 2016

You can download fresh questions. Daily updated. 

LAST UPDATE: TODAY 

1 
Fill in the blank.
The decimal equivalent of the binary number 10010101 is    “149” .
2. Match each IPv4 address to the appropriate address category. (Not all options are used.)

Place the options in the following order:

Host address [A] 192.168.100.161/25 [A]

Host address [B] 203.0.113.100/24 [B]

Host address [C] 10.0.50.10/30 [C]

Network address [D] 192.168.1.80/29 [D]

Network address [E] 172.110.12.64/28 [E]

Network address [F] 10.10.10.128/25 [F]

Broadcast address [G] 10.0.0.159/27 [G]

Broadcast address [H] 192.168.1.191/26 [H]

3 
What is indicated by a successful ping to the ::1 IPv6 address?

The link-local address is correctly configured.

The default gateway address is correctly configured.

The host is cabled properly.

All hosts on the local link are available.

IP is properly installed on the host.*

4

Launch PT – Hide and Save PT
Open the PT Activity. Perform the tasks in the activity instructions and then answer the question.

Which message is displayed on the web server?

Correct configuration!*

IPv6 address configured!

You did it right!

Successful configuration!

5 
Which two ICMP messages are used by both IPv4 and IPv6 protocols? (Choose two.)​

router solicitation

protocol unreachable*

neighbor solicitation

route redirection*

router advertisement

6 
A message is sent to all hosts on a remote network. Which type of message is it?

unicast

directed broadcast*

limited broadcast

multicast

7 
Which two things can be determined by using the ping command? (Choose two.)

the average time it takes each router in the path between source and destination to respond

the average time it takes a packet to reach the destination and for the response to return to the source*

whether or not the destination device is reachable through the network*

the IP address of the router nearest the destination device

the number of routers between the source and destination device

8 
A DHCP server is used to assign IP addresses dynamically to the hosts on a network. The address pool is configured with 192.168.10.0/24. There are 3 printers on this network that need to use reserved static IP addresses from the pool. How many IP addresses in the pool are left to be assigned to other hosts?

253

252

251*

254

9 
Which two parts are components of an IPv4 address? (Choose two.)

logical portion

network portion*

physical portion

broadcast portion

host portion*

subnet portion

10 
Which IPv6 address is most compressed for the full FE80:0:0:0:2AA:FF:FE9A:4CA3 address?​

FE80::2AA:FF:FE9A:4CA3*

FE80::0:2AA:FF:FE9A:4CA3​

FE80:::0:2AA:FF:FE9A:4CA3​

FE8::2AA:FF:FE9A:4CA3​

11. Match each description with an appropriate IP address. (Not all options are used)

169.254.1.5 -> a link-local address
192.0.2.153 -> a TEST-NET address
240.2.6.255 -> an experimental address
172.19.20.5 -> a private address
127.0.0.1 -> a loopback address

12 
What are three parts of an IPv6 global unicast address? (Choose three.)

an interface ID that is used to identify the local host on the network*

an interface ID that is used to identify the local network for a particular host

a subnet ID that is used to identify networks inside of the local enterprise site*

a global routing prefix that is used to identify the network portion of the address that has been provided by an ISP*

a global routing prefix that is used to identify the portion of the network address provided by a local administrator

13. Match each description with an appropriate IP address. (Not all options are used.)

192.31.18.123 -> a legacy class C address
198.256.2.6 -> an invalid IPv4 address
64.100.3.5 -> a legacy class A address
224.2.6.255 -> a legacy class D address
128.107.5.1 -> a legacy class B address

14 
Which network migration technique encapsulates IPv6 packets inside IPv4 packets to carry them over IPv4 network infrastructures?

encapsulation

translation

dual-stack

tunneling*

15 
When an IPv6 enabled host needs to discover the MAC address of an intended IPv6 destination, which destination address is used by the source host in the NS message?

global unicast address of the receiver

solicited-node multicast address*

all-node multicast address

link-local address of the receiver

16. 
When a Cisco router is being moved from an IPv4 network to a complete IPv6 environment, which series of commands would correctly enable IPv6 forwarding and interface addressing?

Router# configure terminal
Router(config)# interface fastethernet 0/0
Router(config-if)# ip address 192.168.1.254 255.255.255.0
Router(config-if)# no shutdown
Router(config-if)# exit
Router(config)# ipv6 unicast-routing

Router# configure terminal
Router(config)# interface fastethernet 0/0
Router(config-if)# ipv6 address 2001:db8:bced:1::9/64
Router(config-if)# no shutdown
Router(config-if)# exit
Router(config)# ipv6 unicast-routing ***********

Router# configure terminal
Router(config)# interface fastethernet 0/0
Router(config-if)# ipv6 address 2001:db8:bced:1::9/64
Router(config-if)# no shutdown

Router# configure terminal
Router(config)# interface fastethernet 0/0
Router(config-if)# ip address 2001:db8:bced:1::9/64
Router(config-if)# ip address 192.168.1.254 255.255.255.0
Router(config-if)# no shutdown
​

17 
What two statements describe characteristics of Layer 3 broadcasts? (Choose two.)

There is a broadcast domain on each switch interface.

Routers create broadcast domains.*

A router will not forward any type of Layer 3 broadcast packet.

Broadcasts are a threat and users must avoid using protocols that implement them.

A limited broadcast packet has a destination IP address of 255.255.255.255.*

Some IPv6 protocols use broadcasts.

18 
Which two statements are correct about IPv4 and IPv6 addresses? (Choose two.)

IPv6 addresses are represented by hexadecimal numbers.*

IPv6 addresses are 32 bits in length.

IPv4 addresses are 128 bits in length.

IPv4 addresses are represented by hexadecimal numbers.

IPv4 addresses are 32 bits in length.*

IPv6 addresses are 64 bits in length.

19 
What is the prefix length notation for the subnet mask 255.255.255.224?

/26

/28

/27*

/25

20 
Fill in the blank.
What is the decimal equivalent of the hex number 0x3F?   “63”
21 
What are two types of IPv6 unicast addresses? (Choose two.)

anycast

link-local*

multicast

loopback*

broadcast

22. When will a router drop a traceroute packet?

when the router receives an ICMP Time Exceeded message

when the host responds with an ICMP Echo Reply message

when the value in the TTL field reaches zero*

when the values of both the Echo Request and Echo Reply messages reach zero

when the RTT value reaches zero

23. An IPv6 enabled device sends a data packet with the destination address of FF02::1. What is the target of this packet?

all IPv6 configured routers across the network

all IPv6 configured routers on the local link

all IPv6 enabled nodes on the local link*

all IPv6 DHCP servers

24. How many bits are in an IPv4 address?

256

128

64

32*

UPDATE WITH QUESTIONS CCNA v5.1

25. What is a result of connecting two or more switches together?

The number of broadcast domains is increased.
The size of the broadcast domain is increased.*
The number of collision domains is reduced.
The size of the collision domain is increased.

26. Refer to the exhibit. How many broadcast domains are there?

1
2
3
4*

27. What are two reasons a network administrator might want to create subnets? (Choose two.)

simplifies network design
improves network performance*
easier to implement security policies*
reduction in number of routers needed
reduction in number of switches needed

28. Refer to the exhibit. A company uses the address block of 128.107.0.0/16 for its network. What subnet mask would provide the maximum number of equal size subnets while providing enough host addresses for each subnet in the exhibit?

255.255.255.0
255.255.255.128*
255.255.255.192
255.255.255.224
255.255.255.240

29. Refer to the exhibit. The network administrator has assigned the LAN of LBMISS an address range of 192.168.10.0. This address range has been subnetted using a /29 prefix. In order to accommodate a new building, the technician has decided to use the fifth subnet for configuring the new network (subnet zero is the first subnet). By company policies, the router interface is always assigned the first usable host address and the workgroup server is given the last usable host address. Which configuration should be entered into the properties of the workgroup server to allow connectivity to the Internet?

IP address: 192.168.10.65 subnet mask: 255.255.255.240, default gateway: 192.168.10.76
IP address: 192.168.10.38 subnet mask: 255.255.255.240, default gateway: 192.168.10.33
IP address: 192.168.10.38 subnet mask: 255.255.255.248, default gateway: 192.168.10.33*
IP address: 192.168.10.41 subnet mask: 255.255.255.248, default gateway: 192.168.10.46
IP address: 192.168.10.254 subnet mask: 255.255.255.0, default gateway: 192.168.10.1

30 If a network device has a mask of /28, how many IP addresses are available for hosts on this network?

256
254
62
32
16
14*

31. Which subnet mask would be used if 5 host bits are available?

255.255.255.0
255.255.255.128
255.255.255.224​*
255.255.255.240

32. How many host addresses are available on the network 172.16.128.0 with a subnet mask of 255.255.252.0?

510
512
1022*
1024
2046
2048

33. How many bits must be borrowed from the host portion of an address to accommodate a router with five connected networks?

two
three*
four
five
34. A network administrator wants to have the same network mask for all networks at a particular small site. The site has the following networks and number of devices:
IP phones – 22 addresses
PCs – 20 addresses needed
Printers – 2 addresses needed
Scanners – 2 addresses needed

The network administrator has deemed that 192.168.10.0/24 is to be the network used at this site. Which single subnet mask would make the most efficient use of the available addresses to use for the four subnetworks?

255.255.255.0
255.255.255.192
255.255.255.224*
255.255.255.240
255.255.255.248
255.255.255.252
——

35. A company has a network address of 192.168.1.64 with a subnet mask of 255.255.255.192. The company wants to create two subnetworks that would contain 10 hosts and 18 hosts respectively. Which two networks would achieve that? (Choose two.)

192.168.1.16/28
192.168.1.64/27*
192.168.1.128/27
192.168.1.96/28*
192.168.1.192/28

36. A network administrator is variably subnetting a network. The smallest subnet has a mask of 255.255.255.248. How many usable host addresses will this subnet provide?​

4
6*
8
10
12

37. Refer to the exhibit. Given the network address of 192.168.5.0 and a subnet mask of 255.255.255.224, how many total host addresses are unused in the assigned subnets?

56
60
64
68
72*

38. Refer to the exhibit. Considering the addresses already used and having to remain within the 10.16.10.0/24 network range, which subnet address could be assigned to the network containing 25 hosts?

10.16.10.160/26
10.16.10.128/28
10.16.10.64/27*
10.16.10.224/26
10.16.10.240/27
10.16.10.240/28

39. A network administrator needs to monitor network traffic to and from servers in a data center. Which features of an IP addressing scheme should be applied to these devices?

random static addresses to improve security
addresses from different subnets for redundancy
predictable static IP addresses for easier identification*
dynamic addresses to reduce the probability of duplicate addresses

40. Which two reasons generally make DHCP the preferred method of assigning IP addresses to hosts on large networks? (Choose two.)

It eliminates most address configuration errors.*
It ensures that addresses are only applied to devices that require a permanent address.
It guarantees that every device that needs an address will get one.
It provides an address only to devices that are authorized to be connected to the network.
It reduces the burden on network support staff.*

41. Refer to the exhibit. A company is deploying an IPv6 addressing scheme for its network. The company design document indicates that the subnet portion of the IPv6 addresses is used for the new hierarchical network design, with the site subsection to represent multiple geographical sites of the company, the sub-site section to represent multiple campuses at each site, and the subnet section to indicate each network segment separated by routers. With such a scheme, what is the maximum number of subnets achieved per sub-site?

0
4
16*
256

42. What is the prefix for the host address 2001:DB8:BC15:A:12AB::1/64?

2001:DB8:BC15
2001:DB8:BC15:A*
2001:DB8:BC15:A:1
2001:DB8:BC15:A:12
43. Consider the following range of addresses:

2001:0DB8:BC15:00A0:0000::

2001:0DB8:BC15:00A1:0000::

2001:0DB8:BC15:00A2:0000::

…

2001:0DB8:BC15:00AF:0000::

The prefix-length for the range of addresses is __/60__

44. Match the subnetwork to a host address that would be included within the subnetwork. (Not all options are used.)

Place the options in the following order.

— not scored —
192.168.1.68 -> 192.168.1.64/27
— not scored —
192.168.1.48 -> 192.168.1.32/27
192.168.1.121 -> 192.168.1.96/27
45. Refer to the exhibit. Match the network with the correct IP address and prefix that will satisfy the usable host addressing requirements for each network. (Not all options are used.)

Place the options in the following order.

— not scored —
192.168.0.192 /27   -> Network C
— not scored —
192.168.0.0 /25       -> Network A
192.168.0.224 /30  -> Network D
192.168.0.128 /26   -> Network B